Back to Drop in triggers
ELF X2 TRIGGER

ELF X2 TRIGGER

$295.95

ELF X2 TRIGGER

With all the same great craftsmanship and features of the Elf 3-gun trigger,
The new ELF Drop-In X-2 Trigger has been built for performance. The only
AR-15 trigger using aircraft needle bearings, making for an incredibly smooth
and fast trigger pull. Using two fingers together for a precise shot gives a pull
weight as low as <1.5lbs per finger. Alternating fingers enables firing an
average of 20% faster. Pull weight is so easy to adjust it can be done in
seconds without removing the trigger from your lower receiver. A second-tonone
AR-15 drop-in trigger system that is strong and light, made of wire EDM
machined, hardened A2 tool steel and lightweight aircraft-grade aluminum.
Installation can be done in minutes using your AR’s original hammer and
trigger pins.
The amazingly short takeup, glass-rod crisp break and next to zero over-travel
can be compared to the finest custom 1911 triggers. Adjustability puts you in
charge based on your preference. If you are looking for a unique adjustable
trigger that allows rapid fire as well as unmatched precision, this is the trigger
system for you.

Fits any mil-spec AR-15 with removable trigger guard.(Large pin Colt available)
Absolutely Drop-Safe regardless of pull-weight
Easily adjustable from without removing from lower
Benefits a wide variety of AR-15 enthusiasts, including collectors, competitive shooters,
hunters, military, law enforcement and disabled veterans.
Very short pull and reset allows for rapid follow up shots and greater accuracy
Sturdy trigger assembly designed for rugged, trouble-free use; Made of lightweight
aircraft-grade aluminum and hardened steel
Unique design of disconnect allows full 1/4” width eliminating possibility of wear and double-firing
High performance trigger and hammer needle bearings for smoother and faster firing
100% made in America with a Lifetime Guarantee!

Out of stock

SKU: ELFX2 Category: Tags: , , , , ,

Description

ELF X2 Trigger

Buy a Premium USA Made ELF X2 Trigger at The Buffalo

Looking for a premium USA made ELF X2 trigger? Look no further! Whether you’re in need of a standard 3 gun trigger, AK drop in trigger, AR10/.308 drop in trigger, match trigger, service trigger, X2 triggers or more; The Buffalo has you covered. Finding the best USA made ELF X2 Triggers for your AR stops here. Have questions or need assistance choosing the best ELF trigger to best suit your rifle? Call us anytime at 805-206-6705 and one of our experienced specialists will get you pointed in the right direction. If you’re ready to go with this ELF X2 trigger and you’re ready to buy, simply order online from The Buffalo today.

DID YOU KNOW? Buying USA made products like this Elf X2 trigger greatly contributes to American manufacturing, job creation, financial growth and more. Most of all, buying USA made products circulates your hard earned money BACK into the US economy. In addition, as a result of purchasing USA made products, you help eliminate the need for foreign outsourcing. Customers can call or order online today for top quality USA made ELF X2 triggers from The Buffalo Ventura CA. Your source for premium USA made ELF X2 triggers and more

Trigger_Line_BannerX-2_Trigger.600x450

Reviews

There are no reviews yet.

Be the first to review “ELF X2 TRIGGER”

Your email address will not be published. Required fields are marked *

You may also like…

Sale! B5 SYSTEMS – SKELETONIZED GRIPSTOP K-SIZE
B5 SYSTEMS – SKELETONIZED GRIPSTOP K-SIZE
The B5 Systems Grip stop will fit any firearm with dead space every 2 3/8" which is used in the majority of rails and hand guards on the market today. For hand guards with threaded inserts every 2 3/8", such as the LWRC and Warsport etc. you can bolt the gripstop on directly. This is the smaller K-size  model. For those with hand guards with M-LOK, KeyMod slots, holes, or MOE, use the Universal hardware (included)
not rated $49.95 $29.99Add to cart
Sale! B5 systems standard skelentonized gripstop
GRIPSTOP B5 GRIP STOP B5 SKELETONIZED STANDARD GRIPSTOP
Custom Black StealthThe B5 Systems Grip stop will fit any firearm with dead space every 2 3/8" which is used in the majority of rails and handguards on the market today. For hand guards with threaded inserts every 2 3/8", such as the LWRC and Warsport etc. you can bolt the grip stop on directly. This is the Standard size model. For those with hand guards with M-LOK slots, KeyMod, holes, or MOE, use the Universal hardware (included).
not rated $59.95 $29.99Add to cart
Sale! AR15 80% 9mm Dedicated Billet Lower Glock Mag W/ Kit
AR15 80% 9mm Dedicated Billet Lower Glock Mag W/ Kit
These are 80% Gun Point Custom Glock 9mm Billet lower receivers. The Buffalo has an exclusive on this lower.  These are a dedicated 9mm Billet design that comes with all the features in the top of the line Gun Point model but in an 80% configuration. These lowers have all the key features you would expect from a high end manufacturer.NO ROLL PINS!! The roll pin has been replaced with a set screw to eliminate the need of beating on the lower receiver. The rear take down pin detent spring is also held in with a set screw making it easier for you to change buffer tubes. The receiver tension set screw effectively eliminates any unwanted “slop” between upper and lower receivers for superior accuracy.No FFL required. As determined by the firearms technology branch of the ATF, this lower receiver is not classified as a “firearm” as defined by the GCA of 1968. We have the ability ship to your door because 80% lowers are not considered firearms by the ATF. Lead time: May very depending on volume of orders at the time placed
Rated 4.75 out of 5
 $209.99 $200.99Add to cart

Related products

Sale! 7 SIDED KEYMOD RAIL SYSTEM 12.5″
7 SIDED KEYMOD RAIL SYSTEM 12.5″
DESCRIPTION 
  •   1913 Picatinny quad rail
  •   Key Mod sides
  •   6061T6 Aluminum
  •   Class III type 2 hard anodized 
  •   Laser engraved
  •   Larger barrel nut and spanner ring included
  •  Made in the USA 
not rated $209.95 $171.95Add to cart
Sale! ELF 3-Gun Trigger
ELF 3-Gun Trigger
The ELF Drop-In 3-Gun Trigger has been built for winning competitions. The only AR-15 trigger using aircraft needle bearings, making for an incredibly smooth and fast trigger pull. The skeletonized hammer combined with our exclusive .043 double double wound polished piano wire hammer spring make for the fastest lock time on the planet. Pull weight is so easy to adjust it can be done in seconds without removing the trigger from your lower receiver. A second-to-none AR-15 drop-in trigger system that is strong and light, made of wire EDM machined, hardened A2 tool steel and lightweight aircraft-grade aluminum. Installation can be done in minutes using your AR’s original hammer and trigger pins. The 3-Gun trigger may be ordered with a curved or straight shoe. The amazingly short takeup, glass-rod crisp break and next to zero over-travel can be compared to the finest custom 1911 triggers. Adjustability puts you in charge based on your preference. If you are looking for the finest adjustable trigger for your competition AR-15 platform, this is the trigger system for you.  Fits any mil-spec AR-15 (Large pin Colt available) Absolutely Drop-Safe regardless of pull-weight Factory set Pull-weight is approximately 50% lighter than that of a standard AR-15 trigger, providing a great combination of speed and accuracy Adjustable from 4lbs to 2 1/2lbs without removing from lower Exclusive double double wound hammer spring and skeletonized hammer ensure a lock time second to none. Very short pull and reset allows for rapid follow up shots and greater accuracy Sturdy trigger assembly designed for rugged, trouble-free use; Made of lightweight aircraft-grade aluminum and hardened steel Unique design of disconnect allows full 1/4” width eliminating possibility of wear and double-firing High performance trigger and hammer needle bearings for smoother and faster firing A competition trigger that leaves all others behind 100% made in America with a Lifetime Guarantee!
not rated $275.95 $245.95Add to cart
Sale! KE ARMS 9″ DELTA-P KEY MOD FREE FLOAT RAIL SYSTEM
KE ARMS 9″ DELTA-P KEY MOD FREE FLOAT RAIL SYSTEM
DESCRIPTION
  •   1913 Picatinny Qaud Rail 
  •   Key Mod sides
  •   6061T6 Aluminum 
  •   Class type 2 hard anodized
  •   Laser Engraved 
  •   Larger barrel nut and spanner ring included
not rated $169.95 $144.95Add to cart
Sale! KE ARMS DUTY TRIGGER BLACK
KE ARMS DUTY TRIGGER BLACK
- 4.5 LBS adjustable reset - Minimal takeup, overtravel and reset - Precision EDM wired from A2 tool steel - Titanium Nitride coated - Simple drop-in installation
Rated 5.00 out of 5
 $190.95 $165.95Add to cart